6060 T5 Extrusions Grade - Aluminium

Range Enquiry

To enquire about our range or your specific requirements, please contact your local service centre.

Temper Types

The most common temper for 6060 aluminium is:

Properties

Chemical Composition

Chemical Element	% Present
Manganese (Mn)	0.00 - 0.10
Iron (Fe)	0.10 - 0.30
Magnesium (Mg)	0.35 - 0.60
Silicon (Si)	0.30 - 0.60
Copper (Cu)	0.00 - 0.10
Zinc (Zn)	0.00 - 0.15
Titanium (Ti)	0.00 - 0.10
Chromium (Cr)	0.00 - 0.05
Other (Each)	0.00 - 0.05
Others (Total)	0.00 - 0.15
Aluminium (Al)	Balance

Mechanical Properties

Mechanical Property	Value
Proof Stress	120 Min MPa
Tensile Strength	160 Min MPa
Elongation A50 mm	6 Min %
Hardness Brinell	60 HB
Elongation A	8 Min %

General Physical Properties

Physical Property	Value
Density	2.70 g/cm³
Melting Point	655 °C
Thermal Expansion	23.4 x 10^-6/K
Modulus of Elasticity	69.5 GPa
Thermal Conductivity	209 W/m.K
Electrical Resistivity	54 % IACS
Electrical Resistivity	0.032 x 10^-6 Ω .m

Applications

Architectural sections for windows, doors, curtain walls
Interior fittings, frame systems, lighting, ladders, railings, fences
Heat sink sections, electronic modules, electro motor housings
Flexible assembly systems, special machinery elements
Truck and trailer flooring, pneumatic installation, railway, inside applications
Irrigation, heating and cooling pipes
Furniture, office equipment

Characteristics

Very good corrosion resistance
Very good weldability
Good cold formability especially in temper T4
Suitable for anodising

Additional Information

Weldability

Process	Rating
Weldability - Gas	Good
Weldability - Arc	Very Good
Weldability - Resistance	Good
Brazability	Very Good

Process	Rating
Workability - Cold	Good
Machinability	Acceptable
Anodising	Very Good

Find your local Service Centre

Experienced multi-product specialists
In-house state of the art processing facilities
Large fleet of bespoke delivery vehicles

Disclaimer

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon. Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed S online) and manufacturers' data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources. Material supplied by the Company may vary significantly from this data but will conform to all relevant and applicable standards. As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied. Advice given by the Company to any third party is given for that party's assistance only and without liability on the part of the Company. All transactions are subject to the Company's current Conditions of Sale. The extent of the Company's liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.

Aluminium, Commercial Alloy6060 T5 Extrusions

General commercial aluminium alloy.

Range Enquiry

Temper Types

Properties

Alloy 6060

BS EN 573-3

Extrusions Up to 150mm Dia., 15mm WT tube, 5mm WT profiles

BS EN 755-2

Applications

Characteristics

Additional Information

Find your local Service Centre